Announcement
Collapse
No announcement yet.

Home made Les Paul

Collapse
X
  • Time
  • Show
Clear All
new posts

  • #31
    Moar!

    Comment


    • #32
      Freeman builds some nice acoustics and resos.
      Really looking forward to the LP.

      Comment


      • #33
        In!
        Signature...

        Comment


        • #34
          Subscribed! I'm planning to do an LP build next year. It will be my first one. This is already a great resource. Thanks!
          Information is not knowledge
          Knowledge is not wisdom
          Wisdom is not truth
          Truth is not beauty
          Beauty is not love
          Love is not music.
          Music Is The Best.

          - Frank Zappa

          Comment


          • #35
            loving this. i too want to build a les paul....

            Comment


            • #36
              Thanki you all for your wonderful enthusiastic comments and support. What I'll try to do is post a few pictures each day of one stage of the build - that way we can talk about it but it won't become so unwieldy that we can't navigate thru it.

              After the glue was dry on the top to body I trimmed the overhang back with a flush cut router bit and filleted the back with a round off bit. I used both in my new router table which I bought just for this project (told you TAS was bad). Unfortunately I don't seem to have any pictures of those operations, but they are really pretty simple.

              In retrospect what I did next is probably out of sequence. What I think I should have done was to first drill and route the pickup cavities, then do the 4 degree angle of the upper bout for the neck and then route the neck pocket. The reason I say that is that at this point the top and upper bout would have been nice and flat to stick the templates on - you'll see what I mean as we go on.

              Instead I jumped right into carving the top. First step was to make two cuts with the router - one at the final depth of the edge (the recurve) and the other a "contour" on the carved portion of the top. I made a little back stop for the edge of the body on the router table, tyrapped the dust collection hose (my shop vac) and set the bit to the depth I wanted



              Again, no good pictures of actually doing it (my hands were pretty full) but when it was done it looked like this



              Carving between those three datum points with a variety of planes and chisel





              (I love that little plane on the right - it is from Grizzly and I use it all the time)



              Once again, I'm very sorry about the lighting on those pics. Here is measuring the angle for the neck (4 degrees)



              Planing it flat



              and laying out the center line, neck pocket and pickups



              Seems like a reasonable place to quit for the night, more tomorrow.

              Comment


              • #37
                I am loving this too. Build threads, to me, are the most worthwhile threads of all!
                Excellent job so far!
                "Thanks to my trusty safety sphere, I surblibed with only tribial bray dabblage." -Professor Hubert J. Farnsworth

                Visit my guitar forums: http://www.shreddersforum.com

                Comment


                • #38
                  great stuff
                  My Band
                  http://www.youtube.com/watch?v=omejCiU-pWI

                  Comment


                  • #39
                    Well, lets make some holes in the top. In the last session we shaped the top and layed out the location of the neck and the pups.



                    I made a simple little template for the neck pocket out of MDF. Usually I would have just used double sticky tape to hold it in place but there wasn't enough surface area so it took a couple of clamps and a screw



                    Drilled out as much material as I could - the blue tape is a crude depth gauge



                    Routed out what was left



                    Checking the depth, I want the pocket just a hair deeper than the tenon will be



                    Moving on to the neck pickup, this is a commercial template from StewMac



                    and the bridge pickup cavity (like the neck I removed as much as I could with a Forstner bit first) Also notice that I've got a clamp on it - there just wasn't enough flat area to trust double sticky tape



                    When it was done it looked like so (thats an oops from the Forstner bit, I told you the depth gauge was crude)

                    Comment


                    • 20 Blues Man 13
                      20 Blues Man 13 commented
                      Editing a comment
                      just curious , instead of using a hand held pwr drill, why did u not use a drill press to make ur holes, more accurate than the tape

                  • #40
                    This is extraordinarily fascinating. I've taken on some big jobs, but this is out of my scope of ability. It's really inspiring. Thank you for posting such great pics...I look forward to following your progress.

                    Comment


                    • #41
                      Dang, sometimes I wish I owned a woodshop. I'll just have to live vicariously thru your thread.

                      Don't mind me, carry on, you're doing fine.
                      My 9/11 Tribute Song: https://vimeo.com/49284582

                      The 9/11 Wall of Shame (caught stepping in it):
                      http://www.youtube.com/watch?v=T3s4_dkKn8Y
                      http://www.youtube.com/watch?v=x6Xoxaf1Al0
                      http://www.youtube.com/watch?v=-jPzAakHPpk
                      http://www.youtube.com/watch?v=4n7uJ...feature=relmfu
                      https://www.youtube.com/watch?v=QU961SGps8g

                      Comment


                      • #42
                        I like this!

                        Comment


                        • #43
                          Looking great!
                          Good transactions: warriorpoet, lowbrow, Puckman, BlackHatHunter, DracoAran, brianeharmonjr, natasmi, id-man, nbabmf, Splendor, angelhair0, d_dave_c, dcindc (x2), dogbone94, chiro972, coolwaterz, Radiohead, lol (x2), roadscholar, Hammer97e, teleman, torgeot, metalhead666666, zakadams, tincob, Doctor Morbius, HanSolo, danhauk, bennnintexas, Overwhelmed987, The Bear, 9-Pin-Phoenix, Dmerge, D34dBaWx, TomCray, Timmott, Tupelo Son, dogfish, ae3753, Gearhunter, virtuzoso, Meowy, RooSTER-b, mrbrown49

                          Comment


                          • #44
                            Dang, sometimes I wish I owned a woodshop. I'll just have to live vicariously thru your thread.

                            Don't mind me, carry on, you're doing fine.


                            My "woodshop" looks amazingly like a garage.



                            My dream (nightmare to my wife) is to actually build a shop off the garage, I want better control of temperature and humidity and more room for TOOLs

                            Comment


                            • #45
                              I tried to make a guitar once about 20 years back in high school. I recall starting off with a strat sized blank and ending up with something the size just under a steinberger, lol. I can appreciate your skill.

                              Comment

                              Working...
                              X