Jump to content
  • Evans Level 360 Drum Heads- Part 1: Heavy Weight Snare Batter

    By Dendy Jarrett |

    5318eeac549a0.jpg.225028e05074f948f0b6f662e205acd7.jpg

    Are they really a revolution? Let's find out

     

    by Dendy Jarrett

     

    This week I received a box from D’Addario with the Evans Level 360 “Heavy Weight Snare Batter” drumhead and the “EMAD Heavyweight Bass Drum” drumheads. First, we’ll look at the heavy weight snare head to determine if these drumheads live up to their claim of “Technically a drumhead. Technologically a revolution.” We’ll cover the EMAD Bass Drum Head in a later issue.

     

    BACKGROUND

    To understand what sets these heads apart, it's necessary to understand what a bearing edge is and how drumheads have been producedin the past.

             Bearing Edge: This is the part of a drum shell that makes contact with the drumhead. Typically, bearing edges have a cut edge that can vary depending on manufacturer from 30 to 45, or even 60 degrees, in slope. Typically the high edge is on the shell's outside.

             Drumhead Construction: Historically, drumheads are produced in a process by which Mylar (or polyester) is stretched and heat-stamped as it's mounted into an aluminum counter-hoop. The counter-hoop is the drumhead's aluminum ring on which the drum hoop applies downward pressure when it's being tightened. In typical drumhead construction, the Mylar coming out of the counter-hoop slopes inward/upward to where the Mylar intersects the bearing edge.

     

    5318eeac5594a.jpg.f974b1702c5b57231bf96a9e3c9adf27.jpg 

     

    OVERVIEW

    The Level 360 construction technique is different; instead of the Mylar slanting inward and upward, it slopes almost vertically. Here's why this makes a difference.

    If you set a typical drumhead on a drum, you’ll note it has a wobble. This is because the bearing edge meets the head on the Mylar's inward and upward slope instead of resting on the flat horizontal Mylar drumhead plane. We rely on tightening the drum's hoop against the counter-hoop to produce the tension needed to pull it tight to the horizontal underside of the Mylar. I also noticed that when I placed any other head on the drum, there was enough slack so that pressing my finger on the head above the bearing edge created a dimple. This doesn’t happen with the Level 360 head; you can actually feel the bearing edge through the head immediately, and the bearing edge instantly sits flush on the horizontal Mylar of the drumhead.

     

    BENEFITS

    This instant contact of the bearing edge against the horizontal Mylar plane really makes a noticeable difference. The tuning is much, much easier - the drum head sits completely level from the start, so the drum key turns normally reserved for bringing the head down to the bearing edge instead begin the tuning process. This also results in a wider tuning range, which I noticed this more in the low range than in the high range. Because I'm familiar with the Evans G1, I noticed that in the mid-range tuning the heads are very similar; but with this head, you can get a much lower “phat” tuning as well as a much higher “crack.”

    This specific head was the model B14HW, a coated head. The coating is excellent and holds up extremely well under a constant beating. This head also sports an impact patch on the underside (often referred to as a dot; although with Evans, it's not a dot per se but a proprietary design). This helps with the head's endurance. It also helps with dampening (just enough, but not too much).

    It's also important to point out that when I'd finished abusing this head, I removed it to note any abnormalities. This head did not “cup” or “bowl” like other heads I have reviewed.

     

    CONCLUSION

    As drummers, we seem to lock into one brand or another - and when we do, it's hard to accept a change. This head will change your thinking. You’ll suddenly realize that you do have choices, and integrating all of one brand of heads or mixing and matching can make sense. This snare head is one of those that, at the very least, you need to try.

    The Level 360 heavy weight snare batter head lives up to the marketing hype. You’ll immediately notice that it is indeed a technological breakthrough.

     

     

    RESOURCES

    Website:

    http://www.evansdrumheads.com/EvansHome.Page?ActiveID=1194

     

    Video - Evans:

                     

     

    Video: Harmony Central: 

     

                     

     

    Resources for purchasing this and other D’Addario Evans Products

    Level 360 Snare Drum Head

    Level 360 EMAD Heavy Weight Batter Head

    Evans EQ Bass Drum Muffler

    Evans EMAD Tom and Snare Dampener

    Evans Magnetic Drum Key

     

    5318eeac56910.jpg.128f37ef10a414139cc98ffa7f1a3a80.jpgDendy Jarrett is the Publisher and Director of Harmony Central. He has been heavily involved at the executive level in many aspects of the drum and percussion industry for over 25 years and has been a professional player since he was 16. His articles and product reviews have been featured in InTune Monthly, Gig Magazine, DRUM! and Modern Drummer Magazines.



    User Feedback

    Recommended Comments

    • Members

    thanks for the review, d.  sounds pretty cool.. and reasonable price, to boot. (kickback, kickback, lol.)(although, upon second look, link above sends me to g1 head, not 360 head, oops...)anyway, i didn't see mention of coating?  i prefer a coated reverse dot, so this doesn't seem too far (unless no coating.)  i like the idea of it seating better, just sounds natural.  especially for a lower tuning.  i would love to hear a lower tone, instead of a "splat."

    that said, i'm psyched to hear the review of the 360 kick head, as if similar, it's be most appropriate, especially seeing how most go for the low tuning (jaw.)  personally, i've always gone a little more than jaw to get the ring i want, but it'd be nice to get a more natural lower tuning without it sounding "flappy," which is what i'm imagining.

    i've been a remo man for years, but this is the first time i'm actually psyched to play something new.

    keep me posted, man.  thanks dendy...

    Link to comment
    Share on other sites

×
×
  • Create New...