Jump to content
  • How to Test Input Impedance for Guitar Effects and Amps

    By Anderton |

    Prevent "tone suckage" with this simple test procedure

    by Craig Anderton

    Is your guitar sounding run down, tired, dull, and anemic? It may not have the flu but be feeding the wrong kind of input. A guitar pickup puts out relatively weak signals, and the input it feeds can either coddle those signals or stomp on them. It’s all a question of the input’s impedance, so let’s look at a simple test for determining whether that amp or signal processor you’re feeding is a signal coddler or a signal stomper. This article will outline how to test guitar impedance so you can achieve the best sound possible.

    You might think that testing for input impedance is pretty esoteric, and that you need an expensive impedance tester, or at least have to find one of those matchbooks that says, “Learn Electronics at Home in Your Spare Time.” But in this case, testing for guitar impedance is pretty simple. You’ll need a standard issue analog or digital volt-ohmmeter (VOM), as sold by electronics stores, and other online stores. You may be able to find a good digital model that cost less than $40. This is one piece of test equipment no guitarist should be without anyway, as you can test anything from whether your stage outlets are really putting out 117V to whether your cable is shorted. You’ll also need a steady test tone generator, which can be anything from an FM tuner emitting a stream of white noise to a synthesizer set for a constant tone (or even a genuine test oscillator).

    What Is Input Impedance?

    If theory scares you, skip ahead to the next subhead. If you can, though, stay tuned since guitar input impedance crops up a lot if you work with electronic devices. Input Impedance is a pretty complex subject, but we can just hit the highlights for the purposes of this article.

    An amp or effect’s input impedance essentially drapes a resistance from the input to ground, thus shunting some of your signal to ground. The lower the resistance to ground, the greater the amount of signal that gets shunted.

    The guitar’s output impedance, which is equivalent to putting a resistance in series with your guitar and the amp input, works in conjunction with the input impedance to impede the signal. If you draw an equivalent circuit for these two resistances, it looks suspiciously like the schematic for a volume control (Fig. 1).




    Fig. 1: The rough equivalent of impedance, expressed as resistance.

    If the guitar’s output impedance is low and the amp input impedance is high, there’s very little loss. Conversely, a high guitar output impedance and low amp input impedance creates a lot of loss.

    The reason why a low input impedance "dulls" the sound is because a guitar pickup’s output impedance changes with frequency—at higher frequencies, the guitar pickup exhibits a higher output impedance. Thus, low frequency signals may not be attenuated that much, but high frequencies could get clobbered.

    Buffer boards and on-board preamps can turn the guitar output into a low impedance output for all frequencies, but many devices are already designed to handle guitars, so adding anything else would be redundant. The trick is finding out which devices are guitar-friendly, and which aren’t; you have to be particularly careful with processors designed for the studio, as there may be enough gain to kick the meters into the red but not a high enough input impedance to preserve your tone. Hence, the following test.=

    Impedance Testing

    This test takes advantage of the fact that input impedance and resistance are, at least for this application, roughly equivalent. So, if we can determine the effect’s input resistance to ground, we’re covered. (Just clipping an ohmmeter across a dummy plug inserted in the input jack isn’t good enough; the input will usually be capacitor-coupled, making it impossible to measure resistance without taking the device’s cover off.)

    Wire up the test jig in Fig. 2, which consists of a 1 Meg linear taper pot and two 1/4" phone jacks. Plug in the signal generator and amplifier (or other device being tested), then perform the following steps.



    Fig. 2: The test jig for measuring impedance. Test points are marked in blue.



    1. Set the VOM to the 10V AC range so it can measure audio signals. You may later need to switch to a more sensitive range (e.g., 2.5V or so) if the test oscillator signal isn’t strong enough for the meter to give a reliable reading.

    2. Set R1 to zero ohms (no resistance).

    3. Measure the signal generator level by clipping the VOM leads to test points 1 and 2. The polarity doesn’t matter since we’re measuring AC signals. Try for a signal generator level between 1 and 2 volts AC but be careful not to overload the effect and cause clipping.

    4. Rotate R1 until the meter reads exactly 50% of what it did in step 3.

    5. Be very careful not to disturb R1’s setting as you unplug the signal generator and amplifier input from the test jig.

    6. Set the VOM to measure ohms, then clip the leads to test points 1 and 3.

    7. Measure R1’s resistance. This will essentially equal the input impedance of the device being tested.

    Interpreting The Results

    If the input impedance is under 100k, I’d highly recommend adding a preamp or buffer board between your guitar and amp or effect to eliminate dulling and signal loss. The range of 100k to 200k is acceptable although you may hear some dulling. An input impedance over 200k means the designer either knows what guitarists want or got lucky. Note, however, that more is not always better. Guitar Input impedances above approximately 1 megohm are often more prone to picking up radio frequency interference and noise, without offering much of a sonic advantage.

    So, there you have it: amaze your friends, impress your main squeeze (well, on second thought maybe not), and strike fear into the forces of evil with your new-found knowledge of guitar input impedance. A guitar that feeds the right input impedance comes alive, with a crispness and fidelity that’s a joy to hear. Happy picking—and testing.



      Craig Anderton is Editor Emeritus of Harmony Central. He has played on, mixed, or produced over 20 major label releases (as well as mastered over a hundred tracks for various musicians), and written over a thousand articles for magazines like Guitar Player, Keyboard, Sound on Sound (UK), and Sound + Recording (Germany). He has also lectured on technology and the arts in 38 states, 10 countries, and three languages.


    User Feedback

    Recommended Comments

    • CMS Author

    Here are some important details for those who have never done anything like this before.


    First, readers may not know what a "signal generator" is. You don't need a piece of calibrated lab equipment for this. Most DAWs and audio editing programs have a function to generate a sine wave. For something more portable (I hate to be tied to my computer workstation when doing shop tests or troubleshooting) there are web resources for downloading WAV or MP3 files of sine waves. You can transfer those to a handheld recorder and that becomes your test generator. Alternatively, there are a few apps for mobile devices to generate test tones. You'll need to be creative with cables but that shouldn't be a problem. I have a few cables with common audio connectors on one end and alligator clips on the other end to make it easy to hack together something temporary.


    The article doesn't state where the generator and amplifier or other device under test are to be connected. Since signal flow on a diagram is usually assumed to be left to right, so the generator should be connected to the jack on the left (3). The device under test (DUT - an amplifier or other input device) should be connected to the jack on the right (1).  It really doesn't matter once you understand how a pot works, but it's best to set up a convention.


    As drawn, the pot will be at zero ohms (or, technically, as close to zero as it will get), when the shaft is turned fully counterclockwise with  the pot oriented so that the shaft is pointing toward you. Check it with the Ohms setting on the multimeter just to be sure. 


    Measure the generator level at the jack to be connected to the DUT, but with nothing but the meter there connected yet. Write down the voltage and then connect the DUT with the meter still connected. Then rotate the pot and stop when the voltage across the DUT input has dropped to half the open circuit voltage.


    The drawing show a 1 megohm pot, but some devices have in input impedance greater than that and even with the pot at maximum resistance the voltage at the DUP input won't drop to half the open circuit voltage. You can stop there and be happy that you have an input that's greater than 1 megohm, or you can start tacking 1 megohm resistors in series (between the pot and the right (1) jack) until you can get to half voltage with the pot, and then add the extra resistance to what you read when you measure the pot. You could get a 10 megohm pot, but that reduces the resolution at the low end, should you want to start measuring everything within sight, where line level inputs are typically in the 5 to 20 kilohms.


    Before you go off checking you mic preamp's input impedance, understand that nearly all mic inputs are differential. You can use this same technique and test setup, but you'll need to connect the generator between pins 2 and 3 of the XLR input and ignore pin 1. You'll also want to monitor the preamp to be sure it's not clipping. You may find that the input impedance varies over a small but measurable range as you adjust the input gain of the preamp.


    If the preamp output is connected to a DAW input, you can skip the voltmeter measurement, just set the generator output low enough so that you aren't clipping the preamp, and monitor the output level using a meter in the DAW. First check and jot down the level with the pot at zero ohms, then turn the pot so that the level drops by 6 dB (that's 1/2 the voltage) and measure the pot's resistance.



    Mike Rivers used to write regularly for a few magazines but they won't let him do it any more because all of his articles are too long. He has retired to the safety of on-line writing since adding another page doesn't require selling another ad.



    Link to comment
    Share on other sites

    • Members

    I use a VHT Valvulator as the first thing my guitar goes into to lower the impedance before going into my effects board and i have on at the end of my board too, It restored my dynamics lost in the effects chain and put some analog tone to my multi effects floor units. This article, is to me, a very ignored issue to us guitar player .... great article !!!!

    Link to comment
    Share on other sites

  • Create New...