Members lilgrasshopper Posted August 22, 2012 Members Share Posted August 22, 2012 Sorry I"m confused about this. Got one speaker on the cheap from some dude. Haven't got a chance to test it out yet. There's some knob u can set different clicks...but I dont' know what all that means. Could someone elucidate for me please? Link to comment Share on other sites More sharing options...
CMS Author Craig Vecchione Posted August 22, 2012 CMS Author Share Posted August 22, 2012 It's a speaker intended for a distributed-line installation. What you see installed in buildings for Muzac, public address, etc. Here's a brief guide that'll explain it well: http://www.bhphotovideo.com/find/newsLetter/pro_audio_may07/pro_audio_understand_distributed_audio_may07.jsp You could possibly bypass the internal transformer and use it as a conventional 8 ohm system. Or rat out the guy who stole it (who has ONE d-l speaker for sale???) and use the reward money to get something you really want. Link to comment Share on other sites More sharing options...
Members Coaster Posted August 22, 2012 Members Share Posted August 22, 2012 i installed 4 of those in a room at work as part of a 70v system. they sound quite good if a little low mid heavy (read: slightly muddy but not bad). they get real loud! i dont know if they are useful in live sound, more of a meeting room or grocery store speaker imho (although the best grocery store speaker you would ever hear) Link to comment Share on other sites More sharing options...
Members lilgrasshopper Posted August 23, 2012 Author Members Share Posted August 23, 2012 Let's just say I have a crown xls402 amp. Which setting would I need to make this work properly? Here's from the spec (I don't understand it) 100 V Line:Tap 1 = 15 W, Tap 2 = 30 WTap 3 = 60 W, Tap 4 is not used70 V Line:Tap 1 = 7.5 W, Tap 2 =15 WTap 3 = 30 W, Tap 4 = 60 W Here is the amp specs: 570W/ch @ 2 ohms, 400W @ 4 ohms, 260W @ 8 ohms, 800W bridge mono @ 8 ohms, 1,140W bridge mono @ 4 ohms Link to comment Share on other sites More sharing options...
Members agedhorse Posted August 23, 2012 Members Share Posted August 23, 2012 Tap 4 is probably the cloaest match, when operated from the amp in stereo mode. Note that the real power handling of the speaker is quiet low AND you MUST high pass the signal at about 50-70Hz or you may saturate the transformer. You will need to look up[ the application specs on this specific speaker. You sure it's not hot? That's an unusual way to get a speaker like this. Link to comment Share on other sites More sharing options...
Members dedmeet Posted August 23, 2012 Members Share Posted August 23, 2012 OP, here is a link to the product page for this speaker: http://www.jblpro.com/catalog/general/Product.aspx?PId=186&MId=2 Like CraigV said, this particular speaker is designed for a distributed line situation using specialty 70/100V amp systems, not for general-purpose PA use off a conventional amplifier. Trying to drive one off an XLS402 in any fashion is likely to result in fried gear. Link to comment Share on other sites More sharing options...
Members lilgrasshopper Posted August 23, 2012 Author Members Share Posted August 23, 2012 Will a regular home theater receiver with 70 watts rms be ok to drive this speaker? Link to comment Share on other sites More sharing options...
Members Bobby1Note Posted August 23, 2012 Members Share Posted August 23, 2012 Looks to me like you're confusing watts and volts. You should have asked here, before buying that speaker. Link to comment Share on other sites More sharing options...
Members Coaster Posted August 23, 2012 Members Share Posted August 23, 2012 here is a pic of two of the four i have installed in this room. they are hooked to a crown 280A which is a 70V amp. in this room they are quite loud. the room is setup for layback and a live mic in the room, but nothing more and its quite effective at this. i would never ever run a band though them. Link to comment Share on other sites More sharing options...
Members agedhorse Posted August 24, 2012 Members Share Posted August 24, 2012 OP, here is a link to the product page for this speaker: http://www.jblpro.com/catalog/general/Product.aspx?PId=186&MId=2Like CraigV said, this particular speaker is designed for a distributed line situation using specialty 70/100V amp systems, not for general-purpose PA use off a conventional amplifier. Trying to drive one off an XLS402 in any fashion is likely to result in fried gear. Won't blow anything up, but you need to understand how 70 volt distribution works. At 70 volts, the speaker will dray 60 watts on the tap I suggested. The speaker acts like 64 ohms and the amp that the OP has will deliver ~30 watts into 64 ohms. Bridging would result in ~90 volts (rough guess) and that might be ok but not for starters. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.