Jump to content
  • Neutrik "Timbre Plug" for Guitar

    By Anderton |

    Here's a clever way for guitarists to tame the "crispiness" of audio interface direct inputs 

     

    By Craig Anderton

     

    dscn2906-d46cf36f.thumb.jpg.26c7d5374ab2e9653dc79495b6e29eec.jpgMost guitarists are aware that with passive pickups, cable capacitance affects tone when feeding a high-impedance input, like the DI inputs on audio interfaces. Activating your guitar’s tone control will tend to “swamp out” any differences caused by cable capacitance, but if the tone control isn’t play, then cable capacitance will nonetheless affect your sound.

     

    Quantifying this difference is more difficult. Different cables have different amounts of capacitance per foot, and the longer the cable, the greater the capacitance. So often when guitar players find a cable that sounds “right,” they’ll just stick with that until it dies (or they do).

     

    Part of what inspired me to write this is a comment in another Forum that Shall Go Nameless that dissed the Timbre Plug (of course, without ever actually trying it) because of the assumption that it just duplicates what a tone control does. But a tone control is more complex than most people realize; it doesn’t just roll off highs, but also interacts with passive pickups to create a resonant peak. This boosts the signal somewhat, and is one reason why rolling back on the tone control sounds “creamier.” It’s also why guitarists like to experiment with different tone control capacitors. Within reason, the higher the capacitor value, the lower the resonant frequency.

     

    dscn2909-637c9896.thumb.jpg.9eeaa29253aecce70c3386a80b7b7332.jpg 

    So yes, cables do make a difference. Yet these days, a lot of guitar players will record by going through a relatively short cable into an audio interface, so cable capacitance doesn’t enter into the picture. Which at long last brings us to the Neutrik NP2RX-TIMBRE, which typically costs under $20.

     

    Let’s take a closer look. The knob opposite the plug shaft itself has a four position rotary switch. It chooses among no capacitance, and three possible capacitor values strapped between the hot and ground connections (Neutrik preferred I not mention the exact values, but they're in the single-digit nanoFarad range). Note that these capacitors are potted in with a switch assembly, so don’t expect to change them if you’d prefer to try different values.

     

    Each of these has a distinct effect on the sound, as you can hear in this demo video.

     

     

    ASSEMBLY

     

    It’s actually quite easy to assemble; you’ll need a Phillips head screwdriver, pencil tip soldering iron, wirecutters, and two-conductor shielded cable with an outside diameter of 0.16” to 0.27”.

     

    assembly-4350c1d2.png.743a3770e111861b49f3e60204e88d23.png

    The assembly instructions are downloadable from the Neutrik web site, and also are printed on the back of the packaging.

     

    I make my cables using the Planet Waves Cable Station, which uses ¼” cable. It was a tight fit, but by following the assembly instructions and cutting the wire exactly as specified, it all went together as expected. I certainly would advise against using anything thicker.

     

    IN USE

     

    Some people may think the right-angle jack is an issue, but it fits fine with a Strat and of course, it ideal for front-facing jacks as found on SG and 335-type guitars. However, ultimately it doesn’t really matter because the cable isn’t “polarized”—you can plug the Timbre plug into your amp or interface. All you give up is the ability to have the controls at your fingertips while you play, but I tend to think this would be a more “set and forget” type of device anyway.

     

    timbre-plug-3554c55a.png.5af130521cde428660e20f29a8b437ca.png

     The Timbre Plug inserted into a TASCAM US-2x2 interface’s direct input.

     

    CONCLUSIONS

     

    The concept of emulating cable capacitance isn’t new, although sometimes it’s just a high-frequency rolloff—which is not the same as a capacitor interacting with a pickup. Neutrik’s solution is compact, built solidly, truly emulates physical cable capacitance, is accessible to anyone with moderate DIY skills, and isn’t expensive. In a way, it's like a hardware "plug-in" for your computer - and you may very well find it’s just the ticket to taking the “edge” off the crispiness that’s inherent in feeding a passive pickup into a high-impedance input.

     

    Buy at B&H

     __________________________________________

     

    image_86469.jpg Craig Anderton is Editorial Director of Harmony Central. He has played on, mixed, or produced over 20 major label releases (as well as mastered over a hundred tracks for various musicians), and written over a thousand articles for magazines like Guitar Player, Keyboard, Sound on Sound (UK), and Sound + Recording (Germany). He has also lectured on technology and the arts in 38 states, 10 countries, and three languages.

     




    User Feedback

    Recommended Comments

    • Members

    I must be missing something. Why you are disassembling the plug and hardwiring a cable to it? Can't you just plug it into the audio unit and plug your guitar cable into that? Or use it as it was intended, plugged into the guitar and thence plugged into the amp or audio unit?

    Link to comment
    Share on other sites

    • Members

    This item seems to be only available from  electronic parts outlets w/min. orders of $30-50, so it's not cheap enough for me to experiment with. I also don't understand why you want to install a hard-wired cable on it. Can't you just plug a cable in?

     

    Link to comment
    Share on other sites

    • Members

    Word on the 'tubes is that the capacities are 1nF, 2.2 nF and 3.3 nF: https://www.youtube.com/watch?v=5qYvw9J6BhY&lc=RwrLBl6NlL6kAR4jOr1qFBaY0nmyGJio4-Pl4DyO_e8 . Those values seem to be a bit too high to simulate normal levels of cable-darkening: they're more in make-your-Strat-coil-sound-like-a-humbucker territory. (For anyone who's interested, Helmuth Lemme's table is handy here: https://www.buildyourguitar.com/resources/lemme/table.htm . Lemme gives a rough range of 300 - 1000 pF (0.3 - 1 nF) for cable capacitance http://www.buildyourguitar.com/resources/lemme/ but I'm pretty sure that doesn't quite reflect the extremes of short runs of modern, high-end cable on one end and truly nasty (or deliberately high-capacitance) old cable runs on the other. http://www.sengpielaudio.com/calculator-centsratio.htm is also useful here, for converting between Hz figures and musical pitches and intervals.)

    But a guitar site shouldn't have to rely on the manufacturers to tell it the capacitance (or inductance) of a passive component (including passive guitars and guitar pickups) these days. Mojotone is selling the Extech 380193 LCR meter http://www.mojotone.com/guitar-parts/Pickup-Winding-Tools/Extech-LCR-Meter-Model-380193#.VlYYdHbhAb8 for $220 plus whatever as "the industry standard for measuring guitar pickups inductance, capacitance and resistance". From grey resellers on eBay you can get the DER EE DE-5000, apparently even higher-spec than the Extech, for $100 plus shipping.

    Link to comment
    Share on other sites


×
×
  • Create New...